Maytag Washer Stuck on Wash Cycle? Try these PROVEN Fixes

Having your Maytag washer stuck on the wash cycle is the last thing you would want, especially when you have a load of laundry to work on.

In this guide, you will learn various reasons for this problem and solutions to get your Maytag washing machine back to work.

The instructions in this guide apply to both Maytag front loader and top loader washers.

Maytag Washing Machine Stuck on Wash Cycle

Your Maytag washing machine can be stuck on wash because of some technical glitches or door lid switch malfunction. It could also be because of an unbalanced load, damaged drain hose, or faulty control board.

I will explain these issues in-depth, along with solutions to troubleshoot the problem.

If your Maytag washing machine is under warranty, I recommend contacting Maytag support and asking for advice. Unfortunately, opening your Maytag washer will void its warranty in most cases, so leave it as a last option.

Reset your Washing Machine

Resetting Washer

Mostly, your Maytag washer is stuck on the wash cycle due to technical glitches in its program or board. These problems can be quickly resolved by simply resetting your washer.

So, the first step in troubleshooting your Maytag washer when it is stuck on the wash cycle is to reset it.

Check the Door Lid Switch

Washer Door Latch Switch

The door latch on the Maytag washing machine is designed to prevent the door from opening during the wash cycle.

The washer safety system will continue operating if the door is closed correctly. When the door is closed, a feedback switch sends a signal to the washer control board. If this switch malfunctions during the cycle, your washing machine will perform abnormally, such as stuck in wash cycle.

The door latch or lid switch is located beneath the control board. So if your Maytag washer is under warranty, do not try to test it yourself, as it will void its warranty.

Even if your washer warranty period is over, I’d recommend seeking a professional help to test or replace the door latch switch on your Maytag washer.

Balance the Load

Washer Balanced Load

Another common cause of Maytag washers getting stuck in the wash cycle is the uneven load. Remember, each washer has a specific capacity beyond or below which it cannot operate.

It is essential to ensure the load is balanced correctly and the washer adequately loaded. Try removing some clothes from your washer and try again.

Similarly, if it has only a few items, add more clothes and then try again.

Inspect and Tighten Drain Hose

Washer Drain Hose

The drain hose is where the used water is pumped out of the washer. If your Maytag washer get stuck in the wash cycle, then it’s might be due to drain hose, which is either damaged or loose.

To check the drain hose, first, disconnect your Maytag washing machine from the power source. Then, access the drain hose and make sure it is properly tightened in its place. Also, check it for any clogs or obstructions.

Check the Washer Timer

Washer Timer

If your Maytag washing machine is automatic or semi-automatic, its functions depend on the timer. The washer controller is programmed as per your set washing cycle instructions.

If the timer on your Maytag washer is faulty, it might get stuck when shifting from wash to wash or from wash to spin.

Testing and replacing the washing machine timer is not something I’d recommend doing yourself, so always seek professional help.

Faulty Control Board

Washer Control Board

If none of the above fixes the problem on your Maytag washing machine and it is still getting stuck in the wash cycle, then its control board might have malfunctioned.

As its name suggests, the control board is the brain of electronic washers. If the control board of your Maytag washing machine malfunctions, it will not operate as it should.

The control board is inside the washing machine, so you must disconnect your Maytag washer from the power source before accessing it.

If your Maytag washer is under warranty, do not attempt to inspect or replace the control board yourself, as it will void its warranty.


Here’s how to fix your Maytag washer when it gets stuck in the wash cycle:

  • Reset your washing machine
  • Check the door lid switch
  • Balance the load
  • Inspect and tighten the drain hose
  • Check your washing machine timer
  • Inspect the control board
Was this page helpful?

Leave a Comment