Summary
Having your Whirlpool washer stuck on the rinse cycle is the last thing you would want, especially when you have a load of laundry to work on.
In this guide, you will learn various reasons for this problem and solutions to get your Whirlpool washing machine back to work.
The instructions in this guide apply to both Whirlpool front loader and top loader washers.
Whirlpool Washing Machine Stuck on Rinse Cycle
Your Whirlpool washing machine can be stuck on rinse because of some technical glitches or door lid switch malfunction. It could also be because of an unbalanced load, damaged drain hose, or faulty control board.
I will explain these issues in-depth, along with solutions to troubleshoot the problem.
If your Whirlpool washing machine is under warranty, I recommend contacting Whirlpool support and asking for advice. Unfortunately, opening your Whirlpool washer will void its warranty in most cases, so leave it as a last option.
Reset your Washing Machine
Mostly, your Whirlpool washer is stuck on the rinse cycle due to technical glitches in its program or board. These problems can be quickly resolved by simply resetting your washer.
So, the first step in troubleshooting your Whirlpool washer when it is stuck on the rinse cycle is to reset it.
Check the Door Lid Switch
The door latch on the Whirlpool washing machine is designed to prevent the door from opening during the wash cycle.
The washer safety system will continue operating if the door is closed correctly. When the door is closed, a feedback switch sends a signal to the washer control board. If this switch malfunctions during the cycle, your washing machine will perform abnormally, such as stuck in rinse cycle.
The door latch or lid switch is located beneath the control board. So if your Whirlpool washer is under warranty, do not try to test it yourself, as it will void its warranty.
Even if your washer warranty period is over, I’d recommend seeking a professional help to test or replace the door latch switch on your Whirlpool washer.
Balance the Load
Another common cause of Whirlpool washers getting stuck in the rinse cycle is the uneven load. Remember, each washer has a specific capacity beyond or below which it cannot operate.
It is essential to ensure the load is balanced correctly and the washer adequately loaded. Try removing some clothes from your washer and try again.
Similarly, if it has only a few items, add more clothes and then try again.
Inspect and Tighten Drain Hose
The drain hose is where the used water is pumped out of the washer. If your Whirlpool washer get stuck in the rinse cycle, then it’s might be due to drain hose, which is either damaged or loose.
To check the drain hose, first, disconnect your Whirlpool washing machine from the power source. Then, access the drain hose and make sure it is properly tightened in its place. Also, check it for any clogs or obstructions.
Check the Washer Timer
If your Whirlpool washing machine is automatic or semi-automatic, its functions depend on the timer. The washer controller is programmed as per your set washing cycle instructions.
If the timer on your Whirlpool washer is faulty, it might get stuck when shifting from wash to rinse or from rinse to spin.
Testing and replacing the washing machine timer is not something I’d recommend doing yourself, so always seek professional help.
Faulty Control Board
If none of the above fixes the problem on your Whirlpool washing machine and it is still getting stuck in the rinse cycle, then its control board might have malfunctioned.
As its name suggests, the control board is the brain of electronic washers. If the control board of your Whirlpool washing machine malfunctions, it will not operate as it should.
The control board is inside the washing machine, so you must disconnect your Whirlpool washer from the power source before accessing it.
If your Whirlpool washer is under warranty, do not attempt to inspect or replace the control board yourself, as it will void its warranty.
Conclusion
Here’s how to fix your Whirlpool washer when it gets stuck in the rinse cycle:
- Reset your washing machine
- Check the door lid switch
- Balance the load
- Inspect and tighten the drain hose
- Check your washing machine timer
- Inspect the control board
